High-Current Floor-Mounted LiFePO4 Battery
51.2V 314Ah 16kWh Floor-Mounted LiFePO4 Battery
MODEL · ELESHELL 16K
ELESHELL 16K is a 51.2V 314Ah floor-mounted LiFePO4 battery with 16kWh nominal energy and 200A maximum charge/discharge current. The moveable-roller enclosure supports CAN, RS485 and RS232 communication, IP54 protection and up to 15 parallel units. It is designed for larger low-voltage storage projects where inverter current capability, cable sizing and installation access are verified first.
For installers and project buyers planning higher-current residential or low-voltage solar storage systems with a single 16kWh enclosure.
Technical values are based on the supplied LeforESS catalog and remain subject to the selected model datasheet.
High-Current Selection
When a 5kWh or 10kWh Battery Is Too Small
ELESHELL 16K combines a larger single-enclosure energy capacity with a stated 200A current limit. The inverter, protection devices and conductors must be designed for the actual current used by the project.
Higher-Power Low-Voltage Inverters
Support projects that require more battery current after the exact inverter limits and BMS protocol are matched.
Extended Residential Backup
Provide more stored energy for a defined group of loads without dividing the capacity across several small wall batteries.
Expandable Battery Banks
Scale beyond one enclosure where the inverter, busbar, communication and protection architecture allow parallel operation.
Verified Product Data
ELESHELL 16K Technical Data
The table follows the brochure specification block. A dimension conflict in the accompanying drawing is called out below.
| Electrical | Nominal voltage | 51.2V |
|---|---|---|
| Nominal capacity | 314Ah | |
| Nominal energy | 16kWh | |
| Maximum charge/discharge current | 200A | |
| Maximum parallel quantity | 15 units | |
| Battery | Chemistry | LiFePO4 |
| Cycle life | >8,000 cycles at 80% DoD and 25°C | |
| Cooling | Natural cooling | |
| Communication | Interfaces | RS485 / CAN / RS232 |
| Mechanical | Installation | Floor mounting with moveable rollers |
| Dimensions (H x W x D) | 750 x 412 x 235mm – brochure table value | |
| Weight | 121kg | |
| Environment | Operating temperature | 0-55°C |
| Protection | Protection level | IP54 |
| Certification | Listed in brochure | UN38.3, CE-EMC, IEC 62619, MSDS and RoHS |
Product specifications and configuration options must be confirmed against the selected model datasheet before ordering. The brochure table states 750 x 412 x 235mm, while the dimension drawing appears to show approximately 750 x 415 x 255mm. Confirm the latest mechanical drawing before ordering.
Current & Cabinet Design
200A System Matching in a Moveable Floor Cabinet
The rollers make the cabinet easier to position during installation; they do not make it a portable power product. The battery should operate in its approved stationary location with suitable cable support and protection.
Technical Buying Questions
ELESHELL 16K Engineering Checks
Does a 200A battery guarantee 200A system output?
No. Actual current is limited by the inverter, BMS settings, state of charge, temperature, cables and protection equipment. Use the lowest confirmed system limit.
Is the roller cabinet a portable battery?
No. It is a floor-mounted energy storage battery. The rollers support positioning during installation; the final operating arrangement must be stable and electrically protected.
Can several ELESHELL 16K batteries run in parallel?
The brochure lists up to 15 units. Confirm the inverter's supported quantity, busbar layout, equal-length cabling and communication settings.
Which cabinet dimensions should be used?
The specification table states 750 x 412 x 235mm, while the diagram appears to show different width and depth values. Obtain the current mechanical drawing before ordering or planning the room.
Is IP54 sufficient for an outdoor site?
IP54 is the brochure rating, not approval for every outdoor condition. Review rain, dust, temperature, drainage, sunlight, enclosure placement and local code.